6 ©2026 Johnstone Supply, LLC DIRECT DRIVE MOTORS 3-3/8" Diameter Shaded Pole Internally Fan-Cooled Motors Shaded Pole Applications: • For use on fans, blowers and small pumps where motor is isolated from air stream Features: • Continuous duty • Studs: four on 2.84" centers, #8-32 thread • Sleeve bearing, thermal overload protection • Open construction Note: S58-701 has four studs opposite shaft end; S58-786 is double shaft with 3-1/4" extension each end. Order # Mfg. # Diam. HP Volts RPM Speeds F/L Amps Efficiency Shaft Diam. Shaft Length Rot. “A” Dim. Bearing Type Wt. Lbs. Each S58-701 D167 3-3/8" 1/70 115 1500 1 0.70 35% 1/4" 3" CWSE 2-7/8" Slv 2.5 369.00 S58-510 D608 3-3/8" 1/50 230 3000 1 0.60 35% 1/4" 1-5/16" CWSE 3-3/4" Slv 3.0 329.00 S58-224 D130 3-3/8" 1/40 115 1500 1 1.00 35% 5/16" 4-1/8" CWSE 3-1/3" Slv 2.8 305.00 S58-786 D209 3-3/8" 1/30 115 3000 1 1.10 35% 1/4" 3-1/4" CCWOSE 3-5/8" Slv 3.0 325.00 S89-088 D208 3-3/8" 1/30 115 3000 1 1.10 35% 1/4" 3" CWSE 3-5/8" Slv 3.0 315.00 11 Frame Replacement Motors Shaded Pole Applications: • Replaces GE motors in air conditioners, unit heaters, commercial condensing units, unit cooler fans, blowers and refrigeration cabinets Features: • Ball bearings, resilient rings for base mounting, and tapped mounting holes Order # Mfg. # Diam. HP Volts RPM Speeds F/L Amps Efficiency Shaft Diam. Shaft Length Rot. “A” Dim. Bearing Type Wt. Lbs. Each S58-534 81671 3-3/8" 1/15 115/230 1550 1 2.10 35% 5/16" 1-5/8" CCWSE 4-1/2" Ball 5.0 449.00 S58-535 81672 3-3/8" 1/15 115/230 1550 1 2.10 35% 5/16" 1-5/8" CWSE 4-1/2" Ball 5.0 485.00 Open Ventilated Air Over Motors for Fans and Roof Ventilators Shaded Pole Replacements for Sears, Acme and Others Applications: • Replacements for motors used on roof ventilators, may also be used on fan and blower applications where the motor is located in the air system Features: • Thermally protected, 60 Hz • Shafts: flatted • Studs: four studs on 3.89" centers, shaft end, 1/2" long all motors • S89-442 is a replacement for Leslie Locke #7108-5056 Fig. Order # Mfg. # Diam. HP Volts RPM Speeds F/L Amps Efficiency Shaft Diam. Shaft Length Rot. “A” Dim. Bearing Type Wt. Lbs. Each A S89-441 D170 4-7/16" 1/20 115 1500 1 1.70 35% 5/16" 2-1/4" CWSE 2-3/4" Slv 4.5 579.00 A S88-238 D116 4-7/16" 1/15 115 1500 1 2.40 35% 3/8" 2-3/8" CWSE 3" Slv 5.0 465.00 A S89-442 D310 4-7/16" 1/12 115 1500 1 4.00 35% 3/8" 2" CWSE 2-3/8" Slv 4.5 545.00 A S87-975 D119 4-2/5" 1/11-1/35 115 1500 3 2.90 35% 1/2" 2-5/8" CCWSE 3-3/4" Ball 6.0 489.00 B S88-229 D174 4-2/5" 1/10 115 1500 1 3.50 35% 3/8" 2-7/8" CWSE 3-3/8" Slv 6.5 599.00 A S89-087 D374 4-2/5" 1/8-1/20 115 1500 2 4.00 35% 3/8" 2-1/2" CWSE 3-5/8" Slv 6.5 919.00 A B
RkJQdWJsaXNoZXIy MjE0NjA2OA==